ASTM F2160 PDF

A major revision to ASTM F has been completed and the new specification will appear in the ” ASTM Book of Specifications Volume Plastic. ASTM F (D) Conduit · Innerduct Warranty · Innerduct Material Specification · F (D & D) Complete Part Number Chart · Enduct True. F (D) Data Sheet · ASTM F Conduit All Types · Innerduct Material Specification · Part Number Chart · Innerduct Warranty · ASTM F (D).

Author: Mikinos Shagor
Country: Cyprus
Language: English (Spanish)
Genre: Love
Published (Last): 13 October 2011
Pages: 125
PDF File Size: 1.69 Mb
ePub File Size: 20.42 Mb
ISBN: 851-5-68170-307-8
Downloads: 17762
Price: Free* [*Free Regsitration Required]
Uploader: Tesida

R2160 electronic file may not be reproduced in any way. Pull Rope and Lubricant The duct should be equipped with a factory installed rope or tape and pre-lubed to aid in the installation of cable. Tensile Properties of Plastics.

High Density Polyethylene Duct

Enter your personal account email address to request a password reset: Check with a manufacturer for specifications. Installation The duct shall be capable of being direct atm by plowing or trenching with no special consideration to using selective backfill. Enter your account email address to request a password reset: HDPE conduit meeting the requirements of this standard shall be made as OD controlled solid wall, with or without internal or external ribs.

c2160 Density of Plastics by the Density Gradient Technique. Link f2610 Active This link will always route to the current Active version of the standard.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The duct specified for aerial installation shall be ultraviolet light-resistant.

  EXADATA DATABASE MACHINE ADMINISTRATION WORKSHOP PDF

Couplings Couplings should be available to quickly connect the duct and should be air and watertight i. Print 1 2 3 4 5 page sstarting from page current page.

This shows different design parameters for polyethylene pipe i. Are you sure you want to empty the cart? Sequentially-Marked Duct – Duct can be ordered with numbering aatm every two feet – printed on the duct.

The internal or external surface may contain a coextruded layer provided the finished conduit meets the specified product requirements. The rope can be provided with varying strengths as needed for a particular installation. Ovality out-of-roundness and curvature are inherent characteristics of coiled, continuous length HDPE conduit. Flow Rates of Thermoplastics by Extrusion Plastometer.

The right to access the electronic files of ASTM Standards is for adtm of viewing for individual use only. Because the fire retardant process eliminates UV protection, Fire-Retardant duct must be installed safe from exposure to UV light.

The internal or external surface may contain a coextruded layer provided the finished conduit meets the specified product requirements. ASTM does not give any warranty express or zstm or make any representation that the contents of this abstract are accurate, complete or up to date. Polyethylene Plastic Pipe and Fittings Materials. Content only available by subscription. There were no books found for the applied search filters.

  ELDAR NIGHT SPINNER PDF

Color The duct for exposed areas black shall have a minimum of carbon black. The duct asmt also be capable of being encased in concrete. The data listed was determined on press molded test specimens, and may therefore deviate from specimens taken from pipes.

Other special markings can be agreed upon between the buyer and seller. No further reproductions authorized. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. Please login to your authorized staff account to use this feature.

HDPE Conduit Types | HDPE Conduit Design | ASTM F Conduit | HDPE Innerduct

Polyethylene Plastics Molding and Extrusion Materials. Seems like pop-ups are blocked for this page. This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a nonpressure application with communication, CATV, or power wire and cables. In addition the electronic files may not be downloaded or distributed elsewhere over computer networks or otherwise.

The internal or external surface may contain a coextruded layer provided the finished conduit meets the product requirements of this specification. Search book title Enter keywords for book title search.